en
fr
ptWinbond 1.2V Serial NOR flash memory
Winbond 1.2V Serial NOR flash, the first flash memory to support ultra-low voltage operation.
What are you looking for?
Products
Home
/
Winbond 1.2V Serial NOR flash, the first flash memory to support ultra-low voltage operation.
The W25Q16 support standard SPI, Dual SPI and Quad SPI operation. Standard SPI instructions use the unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the rising edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output) to read data or status from the device on the falling edge CLK.
Brand:
Winbondbit Unique Serial Number and three 256-bytes Security Registers.
FEATURES
New Family of SpiFlash Memories Flexible Architecture with 4KB sectors
– W25Q16JV: 16M-bit / 2M-byte (2,097,152) – Uniform Sector/Block Erase (4K/32K/64K-Byte)
– Standard SPI: CLK, /CS, DI, DO – Program 1 to 256 byte per programmable page
– Dual SPI: CLK, /CS, IO0, IO1 – Erase/Program Suspend & Resume
– Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
– Software & Hardware Reset(1)
Highest Performance Serial Flash Advanced Security Features
– 133MHz Single, Dual/Quad SPI clocks – Software and Hardware Write-Protect
– 266/532MHz equivalent Dual/Quad SPI – Power Supply Lock-Down and
– 66MB/S continuous data transfer rate – Special OTP protection(2
– Min. 100K Program-Erase cycles per sector – Top/Bottom, Complement array protection
– More than 20-year data retention – Individual Block/Sector array protection
– Individual Block/Sector array protection
Efficient “Continuous Read” – 64-Bit Unique ID for each device
– Continuous Read with 8/16/32/64-Byte Wrap – Discoverable Parameters (SFDP) Register
– As few as 8 clocks to address memory – 3X256-Bytes Security Registers with OTP lock
– Allows true XIP (execute in place) operation – Volatile & Non-volatile Status Register Bits
– Outperforms X16 Parallel Flash
Low Power, Wide Temperature Range Space Efficient Packaging
– Single 2.7V to 3.6V supply – 8-pin SOIC 150-mil / 208-mil
– -40°C to +85°C operating range – 8-pad USON 2X3mm/4x3-mm
– -40°C to +105°C operating range – 8-pad XSON 4x4-mm
– <1µA Power-down (typ.) – 8-pad WSON 6x5-mm
– 8-ball WLCSP
– Contact Winbond for KGD and other options
Winbond 1.2V Serial NOR flash, the first flash memory to support ultra-low voltage operation.
Serial NOR Flash Spi Flash®Memories with SPI, Dual-SPI, Quad-SPI and QPI Part NO. W25Q64JVSSIQ,W25Q64JVSSJQ,W25Q64JVSSBQ,W25Q64JVSSAQ,W25Q64JVSSSQ
Winbond provides a series of Serial NAND products compatible with SPI NOR interface, so that users do not need to continue to rack their brains over the selection of large-capacity memory. In the past, NOR Flash has a relatively good cost advantage in low-volume products, but NAND Flash is a more cost-competitive product in large-volume products.
Winbond offers a range of industry standard SLC NAND from 1Gb to 8Gb. In software and hardware control and interface, it is the same as all SLC NAND in the market. Therefore, users can easily find their own suitable products in the huabang product series to replace them.
*W25M SpiStack product series *Stack memory for various capacity combinations of Flash products *Users can easily choose the size of the required capacity *Standard SPI interface *Compatible with existing SpiFlash
The W25Q128FW (128M-bit) Serial Flash memory provides a storage solution for systems with limited space, pins and power.
DUAL/QUAD SPI For Industrial & Industrial Plus Grade The W25Q256JV supports standard SPI, Dual SPI and Quad SPI operation. Standard SPI instructions use the unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the rising edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output) to read data or status from the device on the falling edge of CLK.
For Industrial & Industrial Plus Grade. The W25Q32JV supports Standard SPI, Dual SPI and Quad SPI operation in each individual stacked die.All 8-bit instructions are shifted into the device through DI (IO0) pin, address and data are shifted in and out of the device through either DI & DO pins for Standard SPI instructions, IO0 & IO1 pins for Dual SPI instructions, or IO0-IO3 pins for Quad SPI instructions.
Indasina, a group corporation composed of factories, is committed to a variety of electronic products and the overall customized solutions.
IPv6 network supported