TCA9534A is a 16-pin device that provides 8-bit general-purpose parallel input and output (I/O) expansion for the two-wire bidirectional I 2C bus (or SMBus) protocol. The device can operate in a supply voltage range of 1.65V to 5.5V, allowing the use of various devices. The device supports 100kHz (standard mode) and 400kHz (fast mode) clock frequencies. When switches, sensors, buttons, LEDs, fans, and other similar devices require additional I/O, I/O expanders (such as TCA9534A) can provide a simple solution.
Brand:
TIDescription
TCA9534A is a 16-pin device that provides 8-bit general-purpose parallel input and output (I/O) expansion for the two-wire bidirectional I 2C bus (or SMBus) protocol. The device can operate in a supply voltage range of 1.65V to 5.5V, allowing the use of various devices. The device supports 100kHz (standard mode) and 400kHz (fast mode) clock frequencies. When switches, sensors, buttons, LEDs, fans, and other similar devices require additional I/O, I/O expanders (such as TCA9534A) can provide a simple solution.
The functions of TCA9534A include generating an interrupt on the INT pin. In this way, the master device knows when the input port status has changed. The hardware selectable address pins A0, A1, and A2 allow up to 8 TCA9534A devices to be on the same I 2C bus. The device can also be powered by power cycling to generate a power-on reset, thereby resetting to the default state. Device
Feature
• Low standby current consumption
• I 2C to parallel port expander
• Open drain circuit low-level effective interrupt output
• 1.65V to 5.5V operating power supply voltage range
• I/O port that can withstand 5V voltage
• 400kHz fast I 2C bus
• 3 hardware address pins can support up to 8 devices on I 2C/SMBus
• Input and output configuration registers
• Polarity inversion registers
• Internal power-on reset
• The channels used are configured as inputs at power-up
• No glitch pulses when powering up
• Noise filter on SCL/SDA input
• Latch output with maximum high current drive capability, suitable for direct drive LED
• Latch-off performance exceeds 100mA, meeting the requirements of JESD 78 Class II )
• Electrostatic discharge (ESD) protection performance exceeds the requirements of JESD 22 specification-2000V human body discharge model (A114-A)-1000V charging device model (C101)
The LM3xxLV family includes the single LM321LV, dual LM358LV, and quad LM324LV operational amplifiers, or op amps. The devices operate from a low voltage of 2.7 V to 5.5 V.
The TLC5941 is a 16-channel, constant-current sink, LED driver. Each channel has an individually adjustable 4096-step grayscale PWM brightness variations between LED channels and other LED Controlled In-Rush Current drivers. Both grayscale control and dot correction are accessible via a serial interface. A single external resistor sets the maximum current value of all 16 channels.
The TPS6104x is a high-frequency boost converter dedicated for small to medium LCD bias supply and white LED backlight supplies. The device is ideal to generate output voltages up to 28 V from a dual-cell NiMH/NiCd or a single-cell Li-Ion battery. The part can also be used to generate standard 3.3-V or 5-V to 12-V power conversions.
The TL431 and TL432 are three-terminal adjustable shunt regulators, with specified thermal stability over applicable automotive, commercial, and military temperature ranges.
8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROLThe TLC548 and TLC549 are CMOS analog-to-digital converter (ADC) integrated circuits built around an 8-bitswitched-capacitor successive-approximation ADC. These devices are designed for serial interface with amicroprocessor or peripheral through a 3-state data output and an analog input. The TLC548 and TLC549 useonly the input/output clock (I/O CLOCK) input along with the chip select (CS) input for data control. Themaximum I/O CLOCK input frequency of the TLC548 is 2.048 MHz, and the I/O CLOCK input frequency of theTLC549 is specified up to 1.1 MHz.
Description This device contains four independent buffers with 3-state outputs. Each gate performs the Boolean function Y = A in positive logic.
The TMP102 device is a digital temperature sensor, which is very suitable as a replacement for NTC/PTC thermistors that require high precision. The device can provide an accuracy of ±0.5°C without calibration or without external component signal conditioning. The device temperature sensor is a highly linear product, and the temperature can be known without complicated calculations or table lookup. The on-chip 12-bit ADC has a minimum resolution of 0.0625°C.
TL431LI/TL432LI is a pin-to-pin replacement of TL431/TL432. TL43xLI provides better stability, lower temperature drift (VI(dev)) and lower reference current (Iref), thereby improving system accuracy.TL431 and TL432 devices are three-terminal adjustable shunt regulators, which can meet the specified thermal stability in the applicable automotive, commercial and military temperature ranges. The output voltage can be set to any value between Vref (approximately 2.5V) and 36V through two external resistors.
Indasina, a group corporation composed of factories, is committed to a variety of electronic products and the overall customized solutions.
IPv6 network supported
