The TPS6104x is a high-frequency boost converter dedicated for small to medium LCD bias supply and white LED backlight supplies. The device is ideal to generate output voltages up to 28 V from a dual-cell NiMH/NiCd or a single-cell Li-Ion battery. The part can also be used to generate standard 3.3-V or 5-V to 12-V power conversions.
Brand:
TIDescription
The TPS6104x is a high-frequency boost converter dedicated for small to medium LCD bias supply and white LED backlight supplies. The device is ideal to generate output voltages up to 28 V from a dual-cell NiMH/NiCd or a single-cell Li-Ion battery. The part can also be used to generate standard 3.3-V or 5-V to 12-V power conversions.
The TPS6104x operates with a switching frequency up to 1 MHz. This frequency allows the use of small external components using ceramic as well as tantalum output capacitors. Together with the thin WSON package, the TPS6104x gives a very small overall solution size. The TPS61040 device has an internal 400-mA switch current limit, while the TPS61041 device has a 250-mA switch current limit, offering lower output voltage ripple and allows the use of a smaller form factor inductor for lower power applications. The low quiescent current (typically 28 μA) together with an optimized control scheme, allows device operation at very high efficiencies over the entire load current range.
Features
• 1.8-V to 6-V Input Voltage Range
• Adjustable Output Voltage Range up to 28 V
• 400-mA (TPS61040) and 250-mA (TPS61041) Internal Switch Current
• Up to 1-MHz Switching Frequency
• 28-μA Typical No-Load Quiescent Current
• 1-μA Typical Shutdown Current
• Internal Soft Start
• Available in SOT23-5, TSOT23-5, and 2-mm × 2-mm × 0.8-mm WSON Packages 2
Applications
• LCD Bias Supply
• White-LED Supply for LCD Backlights
• Digital Still Camera
• PDAs, Organizers, and Handheld PCs
• Cellular Phones
• Internet Audio Players
• Standard 3.3-V or 5-V to 12-V Conversion
The LM3xxLV family includes the single LM321LV, dual LM358LV, and quad LM324LV operational amplifiers, or op amps. The devices operate from a low voltage of 2.7 V to 5.5 V.
TCA9534A is a 16-pin device that provides 8-bit general-purpose parallel input and output (I/O) expansion for the two-wire bidirectional I 2C bus (or SMBus) protocol. The device can operate in a supply voltage range of 1.65V to 5.5V, allowing the use of various devices. The device supports 100kHz (standard mode) and 400kHz (fast mode) clock frequencies. When switches, sensors, buttons, LEDs, fans, and other similar devices require additional I/O, I/O expanders (such as TCA9534A) can provide a simple solution.
The TLC5941 is a 16-channel, constant-current sink, LED driver. Each channel has an individually adjustable 4096-step grayscale PWM brightness variations between LED channels and other LED Controlled In-Rush Current drivers. Both grayscale control and dot correction are accessible via a serial interface. A single external resistor sets the maximum current value of all 16 channels.
The TL431 and TL432 are three-terminal adjustable shunt regulators, with specified thermal stability over applicable automotive, commercial, and military temperature ranges.
8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROLThe TLC548 and TLC549 are CMOS analog-to-digital converter (ADC) integrated circuits built around an 8-bitswitched-capacitor successive-approximation ADC. These devices are designed for serial interface with amicroprocessor or peripheral through a 3-state data output and an analog input. The TLC548 and TLC549 useonly the input/output clock (I/O CLOCK) input along with the chip select (CS) input for data control. Themaximum I/O CLOCK input frequency of the TLC548 is 2.048 MHz, and the I/O CLOCK input frequency of theTLC549 is specified up to 1.1 MHz.
Description This device contains four independent buffers with 3-state outputs. Each gate performs the Boolean function Y = A in positive logic.
The TMP102 device is a digital temperature sensor, which is very suitable as a replacement for NTC/PTC thermistors that require high precision. The device can provide an accuracy of ±0.5°C without calibration or without external component signal conditioning. The device temperature sensor is a highly linear product, and the temperature can be known without complicated calculations or table lookup. The on-chip 12-bit ADC has a minimum resolution of 0.0625°C.
TL431LI/TL432LI is a pin-to-pin replacement of TL431/TL432. TL43xLI provides better stability, lower temperature drift (VI(dev)) and lower reference current (Iref), thereby improving system accuracy.TL431 and TL432 devices are three-terminal adjustable shunt regulators, which can meet the specified thermal stability in the applicable automotive, commercial and military temperature ranges. The output voltage can be set to any value between Vref (approximately 2.5V) and 36V through two external resistors.
Indasina, a group corporation composed of factories, is committed to a variety of electronic products and the overall customized solutions.
IPv6 network supported