The AM26C31 device is a differential line driver with complementary outputs, designed to meet the requirements of TIA/EIA-422-B and ITU (formerly CCITT).
Brand:
TIDescription
The AM26C31 device is a differential line driver with complementary outputs, designed to meet the requirements of TIA/EIA-422-B and ITU (formerly CCITT). The 3-state outputs have high-current capability for driving balanced lines, such as twistedpair or parallel-wire transmission lines, and they provide the high-impedance state in the power-off condition. The enable functions are common to all four drivers and offer the choice of an active-high (G) or active-low (G) enable input. BiCMOS circuitry reduces power consumption without sacrificing speed.
The AM26C31C device is characterized for operation from 0°C to 70°C, the AM26C31I device is characterized for operation from –40°C to 85°C, the AM26C31Q device is characterized for operation over the automotive temperature range of –40°C to 125°C, and the AM26C31M device is characterized for operation over the full military temperature range of –55°C to 125°C.
Features
• Meets or Exceeds the Requirements of TIA/EIA422-B and ITU Recommendation V.11
• Low Power, ICC = 100 μA Typical
• Operates From a Single 5-V Supply
• High Speed, tPLH = tPHL = 7 ns Typical
• Low Pulse Distortion, tsk(p) = 0.5 ns Typical
• High Output Impedance in Power-Off Conditions
• Improved Replacement for AM26LS31 Device
• Available in Q-Temp Automotive
– High-Reliability Automotive Applications
– Configuration Control and Print Support
– Qualification to Automotive Standards
• On Products Compliant to MIL-PRF-38535, All Parameters Are Tested Unless Otherwise Noted. On All Other Products, Production Processing Does Not Necess arily Include Testing of All Parameters.
Applications
• Chemical and Gas Sensors
• Field Transmitters: Temperature Sensors and Pressure Sensors
• Military: Radars and Sonars
• Motor Control: Brushless DC and Brushed DC
• Military and Avionics Imaging
• Temperature Sensors and Controllers Using Modbus
The LM3xxLV family includes the single LM321LV, dual LM358LV, and quad LM324LV operational amplifiers, or op amps. The devices operate from a low voltage of 2.7 V to 5.5 V.
TCA9534A is a 16-pin device that provides 8-bit general-purpose parallel input and output (I/O) expansion for the two-wire bidirectional I 2C bus (or SMBus) protocol. The device can operate in a supply voltage range of 1.65V to 5.5V, allowing the use of various devices. The device supports 100kHz (standard mode) and 400kHz (fast mode) clock frequencies. When switches, sensors, buttons, LEDs, fans, and other similar devices require additional I/O, I/O expanders (such as TCA9534A) can provide a simple solution.
The TLC5941 is a 16-channel, constant-current sink, LED driver. Each channel has an individually adjustable 4096-step grayscale PWM brightness variations between LED channels and other LED Controlled In-Rush Current drivers. Both grayscale control and dot correction are accessible via a serial interface. A single external resistor sets the maximum current value of all 16 channels.
The TPS6104x is a high-frequency boost converter dedicated for small to medium LCD bias supply and white LED backlight supplies. The device is ideal to generate output voltages up to 28 V from a dual-cell NiMH/NiCd or a single-cell Li-Ion battery. The part can also be used to generate standard 3.3-V or 5-V to 12-V power conversions.
The TL431 and TL432 are three-terminal adjustable shunt regulators, with specified thermal stability over applicable automotive, commercial, and military temperature ranges.
8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROLThe TLC548 and TLC549 are CMOS analog-to-digital converter (ADC) integrated circuits built around an 8-bitswitched-capacitor successive-approximation ADC. These devices are designed for serial interface with amicroprocessor or peripheral through a 3-state data output and an analog input. The TLC548 and TLC549 useonly the input/output clock (I/O CLOCK) input along with the chip select (CS) input for data control. Themaximum I/O CLOCK input frequency of the TLC548 is 2.048 MHz, and the I/O CLOCK input frequency of theTLC549 is specified up to 1.1 MHz.
Description This device contains four independent buffers with 3-state outputs. Each gate performs the Boolean function Y = A in positive logic.
The TMP102 device is a digital temperature sensor, which is very suitable as a replacement for NTC/PTC thermistors that require high precision. The device can provide an accuracy of ±0.5°C without calibration or without external component signal conditioning. The device temperature sensor is a highly linear product, and the temperature can be known without complicated calculations or table lookup. The on-chip 12-bit ADC has a minimum resolution of 0.0625°C.
Indasina, a group corporation composed of factories, is committed to a variety of electronic products and the overall customized solutions.
IPv6 network supported