product
Products
Home /

Electronic Components

/

MXIC

/MXIC FLASH MEMORY MX25L1606EM2I-12G SOIC-8_208mil

MXIC FLASH MEMORY MX25L1606EM2I-12G SOIC-8_208mil

3V, 16M-BIT [x 1/x 2]  CMOS SERIAL FLASH MEMORY

Key Features  

• Hold Feature  

• Low Power Consumption  

• Auto Erase and Auto Program Algorithms  

• Additional 512 bit secured OTP for unique identifier

  • Product Details

FEATURES  

GENERAL  

• Single Power Supply Operation   

- 2.7 to 3.6 volt for read, erase, and program operations  

• Supports Serial Peripheral Interface 

-- Mode 0 and  Mode 3  

• 16,777,216 x 1 bit structure or 8,388,608 x 2 bits (Dual  Output mode) structure  

• 512 Equal Sectors with 4K byte each  

- Any Sector can be erased individually  

• 32 Equal Blocks with 64K byte each  

- Any Block can be erased individually  

• Program Capability   

- Byte base  

- Page base (256 bytes)  

• Latch-up protected to 100mA from 

-1V to Vcc +1V  PERFORMANCE  

• High Performance  

- Fast access time: 86MHz serial clock  

- Serial clock of Dual Output mode : 80MHz  

- Fast program time: 0.6ms(typ.) and 3ms(max.)/page  

- Byte program time: 9us (typ.)  

- Fast erase time: 40ms(typ.) /sector ; 0.4s(typ.) /block  

• Low Power Consumption   

- Low active read current: 25mA(max.) at 86MHz   

- Low active programming current: 15mA (typ.)   

- Low active sector erase current: 9mA (typ.)   

- Low standby current: 15uA (typ.)  

- Deep power-down mode 2uA (typ.)  

• Typical 100,000 erase/program cycles  

• 20 years of data retention


SOFTWARE FEATURES  

• Input Data Format   

- 1-byte Command code  

• Advanced Security Features  

- Block lock protection  The BP3-BP0 status bit defines the size of the area  to be software protection against program and  erase instructions  

- Additional 512 bit secured OTP for unique identifier  

• Auto Erase and Auto Program Algorithm  

- Automatically erases and verifies data at selected  sector  

- Automatically programs and verifies data at selected page by an internal algorithm that automatically  times the program pulse widths (Any page to be programed should have page in the erased state first)  

• Status Register Feature  

• Electronic Identification   

- JEDEC 1-byte manufacturer ID and 2-byte device  ID  

- RES command for 1-byte Device ID  

- REMS commands for 1-byte manufacturer ID and  1-byte device ID  

• Support Serial Flash Discoverable Parameters (SFDP)  mode  HARDWARE FEATURES  

• PACKAGE  

- 16-pin SOP (300mil)  

- 8-pin SOP (150mil)  

- 8-pin SOP (200mil)  

- 8-pin PDIP (300mil)  

- 8-land WSON (6x5mm)  

- 8-land USON (4x4mm)  

- 24-Ball BGA  

- All devices are RoHS Compliant and Halogenfree 6  P/N: PM1548 REV. 1.8, JUN 04, 2015  MX2

Send A Message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
If you have questions or suggestions,please leave us a message,we will reply you as soon as we can!
Related Products
MXIC FLASH MEMORY MX25L12835EMI-10G

MXIC FLASH MEMORY MX25L12835EMI-10G SOP-16

HIGH PERFORMANCE  SERIAL FLASH SPECIFICATION128M-BIT [x 1/x 2/x 4] CMOS MXSMIOTM (SERIAL MULTI I/O) FLASH MEMORY

 MX25L6406EM2I-12G

MXIC FLASH MEMORY MX25L6406EM2I-12G SOIC-8_208mil

GENERAL DESCRIPTION  The device feature a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus.  The three bus signals are a clock input (SCLK), a serial data input (SI), and a serial data output (SO). Serial access  to the device is enabled by CS# input.  When it is in Dual Output read mode, the SI and SO pins become SIO0 and SIO1 pins for data output.  The device provides sequential read operation on whole chip.  After program/erase command is issued, auto program/ erase algorithms which program/ erase and verify the specified page or sector/block locations will be executed. Program command is executed on byte basis, or page basis, or  word basis for erase command is executes on sector, or block, or whole chip basis.  To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read  command can be issued to detect completion status of a program or erase operation via WIP bit.  Advanced security features enhance the protection and security functions, please see security features section for  more details.  When the device is not in operation and CS# is high, it is put in standby mode.  The device utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after typical  100,000 program and erase cycles.

MX25L3206EM2I-12G

MXIC FLASH MEMORY MX25L3206EM2I-12G SOP-8

32M-BIT [x 1 / x 2] CMOS SERIAL FLASHGENERAL DESCRIPTION  The device feature a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus.  The three bus signals are a clock input (SCLK), a serial data input (SI), and a serial data output (SO). Serial access  to the device is enabled by CS# input.  When it is in Dual Output read mode, the SI and SO pins become SIO0 and SIO1 pins for data output.  The device provides sequential read operation on whole chip.  After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified page or sector/block locations will be executed. Program command is executed on byte basis, or page basis, or  word basis for erase command is executes on sector, or block, or whole chip basis.  To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read  command can be issued to detect completion status of a program or erase operation via WIP bit.  Advanced security features enhance the protection and security functions, please see security features section for  more details.  When the device is not in operation and CS# is high, it is put in standby mode.  The device utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after typical  100,000 program and erase cycles.

MXIC FLASH MEMORY MX25L12835FM2I-10G SOP8

MXIC FLASH MEMORY MX25L12835FM2I-10G SOP8

3V, 128M-BIT [x 1/x 2/x 4]  CMOS MXSMIO®   (SERIAL MULTI I/O)  FLASH MEMORY

 GD25Q64CSIG

GD FLASH MEMORY GD25Q64CSIG SOP-8

GENERAL DESCRIPTION  The GD25Q64C (64M-bit) Serial flash supports the standard Serial Peripheral Interface (SPI), and supports the  Dual/Quad SPI: Serial Clock, Chip Select, Serial Data I/O0 (SI), I/O1 (SO), I/O2 (WP#), and I/O3 (HOLD#). The Dual I/O  data is transferred with speed of 240Mbits/s and the Quad I/O & Quad output data is transferred with speed of 480Mbits/s.

GD25Q16CSIG

GD FLASH MEMORY GD25Q16CSIG SOP-8_208mil

GENERAL DESCRIPTION  The GD25Q16C(16M-bit) Serial flash supports the standard Serial Peripheral Interface (SPI), and supports the  Dual/Quad SPI: Serial Clock, Chip Select, Serial Data I/O0 (SI), I/O1 (SO), I/O2 (WP#), and I/O3 (HOLD#). The Dual I/O  data is transferred with speed of 240Mbits/s and the Quad I/O & Quad output data is transferred with speed of 480Mbits/s.

free-to-air satellite receiver box

Factory OEM DVB-S2 Receiver Auto Conversion box Free To Air

*DVB-S2 / DVB-S Compatible *True-color OSD and 2D graphics accelerator, anti-flicker filter supported *MPEG-4&H.264,H.263,MPEG-2,JPEG/MJPEG Video Decoding *HDMI port *Video Resolution:1080P/1080i/720p/576P/576i/480p/480i *All of the PAL and NTSC analog TV standards supported *Media Player Support MP4,AVI,MKV,FLV, MPG, VOB, DAT,TS etc *2*USB 2.0, Support PVR/Timeshift/Multi-Media Player *Strong Memory:Up to 100 Satellites,1000TP & 5000 Channels *Support DiSEqC1.0/1.1/1.2/USALS *Supports fast channel blind *Hotstar, YouTube, Google Map, Weather Report, IPTVsupported *Wifi supports MT7601 and RT5370 *Patch: Biss, Powervu(auto) supported *IKS Protocol: Cccam

home CCTV Security 1080P wireless MINI WIFI HD Hidden Spy Camera

Indasina home CCTV Security 1080P wireless MINI WIFI HD Hidden Spy Camera

Home CCTV Security 1080P wireless camera wifi ip mini camera wifi with cloud storage 1)Support WiFi AP function,view angle 140°, built-in strong Antenna. 2)Support Amazon cloud storage 3)1080P video resolution 4)Support TF Card up to 128 GB . 5)One-Way Audio, Motion Detection Alarm, Snapshot, Video and Buzzer function. 6)One Step RPS connection, Multi Language Support.

Please tell us your needs

Indasina, a group corporation composed of factories, is committed to a variety of electronic products and the overall customized solutions.

partners 8
Partners7
Partners6
Partners5
Partners4
Partners3
Partners2
Partners1
Leave a message Request A Free Quote
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.