ML51BB9AE is an enhanced 1T 8051 core microcontroller with built-in Flash. The typical power consumption in normal operation mode can reach 80 μA / MHz and the power consumption in sleep mode can be less than 1 μA. The highest speed of this series can reach 24 MHz, and a built-in 38.4 kHz low-speed internal oscillator supports a wide voltage operating range of 1.8V to 5.5V. Operating temperature:-40 ℃ to 105 ℃.
ML51BB9AE contains 16 K bytes of Flash and an additional 1 K bytes of on-chip auxiliary RAM (XRAM), equipped with a wealth of peripherals, such as 7 general-purpose I / O, 2 serial ports, 1 ISO-7816 interface, 2 groups I²C and 1 set of SPI are available in MSOP10 package.
Wearable devices, smart remote controllers, Internet endpoint devices, smart homes, smoke detection devices, battery devices, etc.
Key features:
• CPU
-Fully static 8-bit 1T 8051 core CMOS microcontroller
-The instruction set is fully compatible with MCS-51
-4-level priority interrupt configuration
-Dual data pointers (DPTRs)
• Working conditions
-Wide voltage operating range 1.8V to 5.5V
-Wide operating frequency up to 24 MHz
-Industrial grade operating temperature-40 ℃ to + 105 ℃
• Low power consumption
-Typical power consumption in normal operation mode 80 μA / MHz
-Typical power consumption of low power operation mode 15 μA
-Low power consumption in idle mode does not exceed 13 μA
-Typical power consumption in power-down mode is less than 1 μA
-Wake-up time in power-down mode is 10 us (HIRC operation)
• RAM
-16 Kbytes APROM for user code
-Configurable 4K / 3K / 2K / 1K byte LDROM, used to start system programming (ISP) code
-Application programming (IAP) memory in APROM with 128 bytes of accumulation per page
-100,000 times flash memory life
-Code security encryption
-256 bytes of on-chip RAM
-Extra 1 Kbytes on-chip auxiliary RAM (XRAM), accessed by MOVX instruction
• Clock source
-24 MHz high-speed internal oscillator (HIRC) ± 1% accuracy class (25 ℃, 3.3V) Accuracy ± 5% accuracy class under full operating conditions
-38.4 kHz low-speed internal oscillator (LIRC) ± 1% accuracy class (25 ℃, 3.3V) Accuracy ± 10% accuracy class under full operating conditions
-External 4 ~ 24 MHz (HXT) crystal oscillator input for precise timing operation
-External 32.768 kHz (LXT) crystal input
-The clock source can be switched by software during operation
-Programmable system clock divider from 1/2, 1/4, 1/6, 1/8…, up to 1/512
• Peripherals
-7 general purpose input and output pins. All output pins have independent 2-level level conversion rate control
-8-channel GPIO interrupt, with edge / level detection, all 7 GPIOs can be configured as one of the input sources
-Standard interrupt pins INT0 and INT1 are compatible with standard 8051
-Two sets of 16-bit timer / counters 0 and 1 compatible with standard 8051
-A set of 16-bit timer 2 with 3-channel input capture module
-A set of 16-bit auto-reload timer 3
-A set of programmable watchdog timer (WDT)
-A set of dedicated self-wake timer (WKT)
-Two full-duplex serial ports
-A set of smart card interfaces support ISO7816-3
-A set of SPI ports support master and slave modes, with a transmission rate of up to 6 Mbps when the system clock is 24 MHz
-Two sets of I²C bus support master and slave mode, data transfer rate up to 400 kpbs
-6 * 16-bit group, 12-channel pulse width modulator (PWM) output, up to 16-bit resolution
-A set of 12-bit ADC, when VDD is greater than 2.5V, the conversion rate is up to 500 Ksps
• Power monitor
-Undervoltage detection (BOD) can be used in low power consumption mode, 7 levels are selectable, configurable interrupt or reset
-Power-on reset (POR)
-Low voltage reset (LVR)
• Strong ESD and EFT capabilities
-ESD HBM passes 8 kV
-EFT> ± 4.4 kV
-Latch test passed 150 mA
• development tools
-Nuvoton Nu-Link based on KEILTM and IAR development environment
-Nuvoton circuit programming (Nu-Link)
-Nuvoton in-system programming (ISP) via UART
Indasina, a group corporation composed of factories, is committed to a variety of electronic products and the overall customized solutions.